View LT1304_147389.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LT1304/LT1304-3.3/LT1304-5 Micropower DC/DC Converters with Low-Battery Detector Active in Shutdown
FEATURES
s s s s s s s s s
DESCRIPTION
The LT(R)1304 is a micropower step-up DC/DC converter ideal for use in small, low voltage, battery-operated systems. The devices operate from a wide input supply range of 1.5V to 8V. The LT1304-3.3 and LT1304-5 generate regulated outputs of 3.3V and 5V and the adjustable LT1304 can deliver output voltages up to 25V. Quiescent current, 120A in active mode, decreases to just 10A in shutdown with the low-battery detector still active. Peak switch current, internally set at 1A, can be reduced by adding a single resistor from the ILIM pin to ground. The high speed operation of the LT1304 allows the use of small, surface-mountable inductors and capacitors. The LT1304 is available in an 8-lead SO package.
, LTC and LT are registered trademarks of Linear Technology Corporation.
5V at 200mA from Two Cells 10A Quiescent Current in Shutdown Operates with VIN as Low as 1.5V Low-Battery Detector Active in Shutdown Low Switch VCESAT: 370mV at 1A Typical 120A Quiescent Current in Active Mode Switching Frequency Up to 300kHz Programmable Peak Current with One Resistor 8-Lead SO Package
APPLICATIONS
s s s s s s
2-, 3-, or 4-Cell to 5V or 3.3V Step-Up Portable Instruments Bar Code Scanners Palmtop Computers Diagnostic Medical Instrumentation Personal Data Communicators/Computers
TYPICAL APPLICATION
2-Cell to 5V Step-Up Converter with Low-Battery Detect
22H* 3 1 VIN LBI 4 SW SENSE LT1304-5 6 ILIM SHDN 7 SHUTDOWN *SUMIDA CD54-220 **1N5817
1304 TA01
D1**
90
499k
8 100k
2 CELLS
100F
604k NC
100F LBO LOW WHEN VBAT < 2.2V
EFFICIENCY (%)
+
+
5V 200mA
80
70
LBO GND 5
2
60 VIN = 3.3V VIN = 2.5V VIN = 1.8V 1 10 100 LOAD CURRENT (mA) 500
1304 TA02
50
40 0.1
U
U
U
Efficiency
1
LT1304/LT1304-3.3/LT1304-5
ABSOLUTE MAXIMUM RATINGS
VIN Voltage ................................................................ 8V SW Voltage ............................................... - 0.4V to 25V FB Voltage (LT1304) ...................................... VIN + 0.3V Sense Voltage (LT1304-3.3/LT1304-5) ..................... 8V ILIM Voltage .............................................................. 5V SHDN Voltage ............................................................ 6V LBI Voltage ............................................................... VIN LBO Voltage ............................................................... 8V Maximum Power Dissipation ............................. 500mW Junction Temperature.......................................... 125C Operating Temperature Range ..................... 0C to 70C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C
PACKAGE/ORDER INFORMATION
ORDER PART NUMBER
TOP VIEW LBI 1 LBO 2 VIN 3 SW 4 8 7 6 5 FB (SENSE)* SHDN ILIM GND
LT1304CS8 LT1304CS8-3.3 LT1304CS8-5 S8 PART MARKING 1304 13043 13045
S8 PACKAGE 8-LEAD PLASTIC SO *FIXED OUTPUT VERSION
TJMAX = 125C, JA = 150C/W
Consult factory for Industrial and Military grade parts.
ELECTRICAL CHARACTERISTICS
PARAMETER Minimum Operating Voltage Operating Voltage Range Quiescent Current Quiescent Current in Shutdown Comparator Trip Point FB Pin Bias Current Sense Pin Leakage in Shutdown Output Sense Voltage Line Regulation LBI Input Threshold LBI Bias Current LBI Input Hysteresis LBO Output Voltage Low LBO Output Leakage Current SHDN Input Voltage High SHDN Input Voltage Low SHDN Pin Bias Current Switch OFF Time Switch ON Time Maximum Duty Cycle Peak Switch Current VSHDN = 5V VSHDN = 0V ISINK = 500A CONDITIONS
VIN = 2V, VSHDN = 2V unless otherwise noted.
MIN
q q
TYP 1.5 120 7 27
MAX 1.65 8 200 15 50 1.26 25 1 3.43 5.25 0.15 1.25 20 65 0.4 0.1 0.4
UNITS V V A A A V nA A V V %/V V nA mV V A V V A A s s % A mA
VSHDN = 2V, Not Switching VSHDN = 0V, VIN = 2V VSHDN = 0V, VIN = 5V LT1304 LT1304 VSHDN = 0V, Fixed Output Versions LT1304-3.3 LT1304-5 1.8V VIN 8V Falling Edge
q q q q q q q q q q q q q q q q q q q
1.22
1.24 10 0.002
3.17 4.80 1.10
3.3 5.05 0.04 1.17 6 35 0.2 0.01
LBI = 1.5V, LBO = 5V
1.4 5 -2 1.5 6 80 1 500 8 2 8 88 1.2
-5 1 4 76 0.8
Current Limit Not Asserted Current Limit Not Asserted ILIM Pin Open, VIN = 5V 20k from ILIM to GND
q q
2
U
W
U
U
WW
W
LT1304/LT1304-3.3/LT1304-5
ELECTRICAL CHARACTERISTICS
PARAMETER Switch Saturation Voltage Switch Leakage CONDITIONS ISW = 1A ISW = 700mA
VIN = 2V, VSHDN = 2V unless otherwise noted.
MIN
q q
TYP 0.37 0.26 0.01
MAX 0.35 7
UNITS V V A
Switch Off, VSW = 5V
The q denotes specifications which apply over the 0C to 70C operating temperature range.
TYPICAL PERFORMANCE CHARACTERISTICS
Switch Saturation Voltage
500 TA = 25C 1.2
SATURATION VOLTAGE (mV)
400
PEAK CURRENT (A)
1.0 0.9 0.8 0.7
TIME (s)
300
200
100
0 0 0.2 0.4 0.6 0.8 SWITCH CURRENT (A) 1.0 1.2
1304 G01
Feedback Voltage
1.250 1.245 1.240 FEEDBACK VOLTAGE (V) BIAS CURRENT (nA) 1.235 1.230 1.225 1.220 1.215 1.210 1.205 1.200 -50 -25 0 25 50 TEMPERATURE (C) 75 100
20 18
14 12 10 8 6 4 2 0 -50 -25 25 50 0 TEMPERATURE (C) 75 100
1304 G05
SUPPLY CURRENT (A)
UW
1304 G04
Peak Switch Current Limit
1.3 8 7 6 5 4 3 2 1 -25 0 25 50 TEMPERATURE (C) 75 100
1304 G02
On- and Off-Times
MAXIMUM ON-TIME
1.1
OFF-TIME
0.6 -50
0 -50
-25
0 25 50 TEMPERATURE (C)
75
100
1304 G03
Feedback Pin Bias Current
300
Supply Current
TA = 25C 250 200 150 100 50 0 VSHDN = VIN NOT SWITCHING
16
VSHDN = 0V 0 1 2 6 4 3 5 INPUT VOLTAGE (V) 7 8
1304 G06
3
LT1304/LT1304-3.3/LT1304-5 TYPICAL PERFORMANCE CHARACTERISTICS
Load Transient Response
VOUT 100mV/DIV AC COUPLED ILOAD 200mA 0 100s/DIV
1304 G07
PIN FUNCTIONS
LBI (Pin 1): Low-Battery Detector Input. When voltage on this pin is less than 1.17V, detector output is low. LBO (Pin 2): Low-Battery Detector Output. Open collector can sink up to 500A. Low-battery detector remains active when device is shut down. VIN (Pin 3): Input Supply. Must be bypassed close (< 0.2") to the pin. See required layout in the Typical Applications. SW (Pin 4): Collector of Power NPN. Keep copper traces on this pin short and direct to minimize RFI. GND (Pin 5): Device Ground. Must be low impedance; solder directly to ground plane. ILIM (Pin 6): Current Limit Set Pin. Float for 1A peak switch current; a resistor to ground will lower peak current. SHDN (Pin 7): Shutdown Input. When low, switching regulator is turned off. The low-battery detector remains active. The SHDN input should not be left floating. If SHDN is not used, tie the pin to VIN. FB/SENSE (Pin 8): On the LT1304 (adjustable) this pin goes to the comparator input. On the fixed-output versions, the pin connects to the resistor divider which sets output voltage. The divider is disconnected from the pin during shutdown.
4
UW
Burst ModeTM Operation
VOUT 100mV/DIV AC COUPLED VSW 5V/DIV
IL 500mA/DIV VIN = 2.5V VOUT = 5V ILOAD = 185mA L = 22H 20s/DIV
1304 G08
Burst Mode is a trademark of Linear Technology Corporation.
U
U
U
LT1304/LT1304-3.3/LT1304-5
BLOCK DIAGRA S
VIN
1
R3 8 R4 FB
Figure 1. LT1304 Block Diagram. Independent Low-Battery Detector A3 Remains Alive When Device Is in Shutdown
8
SENSE
R1 = 355k (LT1304-3.3), 195k (LT1304-5)
W
LBI
+
C1 3
L1 VIN SW
D1 4
+
VOUT C2
2
LB0
1.5V UNDERVOLTAGE LOCKOUT 36mV
+
A2
+
A3 BIAS ~1V
-
1.17V
-
Q3
R2 1k
R1 7.2
OFF
-
A1
ENABLE
+
1.24V VREF
TIMERS 6s ON 1.5s OFF DRIVER
1k Q2 x1 Q1 x200
SHUTDOWN 7 SHDN 6 ILIM 5 GND
1304 F01
LBI 1
LB0 2 1.5V UNDERVOLTAGE LOCKOUT 36mV
VIN 3
SW 4
+
A2
+
A3 BIAS ~1V
-
1.17V 590k
-
Q3
R2 1k
R1 7.2
OFF
-
R1 A1
ENABLE
+
1.24V VREF
TIMERS 6s ON 1.5s OFF DRIVER
1k Q2 x1 Q1 x200
SHUTDOWN SHDN 7 6 ILIM 5 GND
1304 F02
Figure 2. LT1304-3.3/LT1304-5 Block Diagram
5
LT1304/LT1304-3.3/LT1304-5
OPERATIO
The LT1304's operation can best be understood by examining the block diagram in Figure 1. Comparator A1 monitors the output voltage via resistor divider string R3/R4 at the FB pin. When VFB is higher than the 1.24V reference, A2 and the timers are turned off. Only the reference, A1 and A3 consume current, typically 120A. As VFB drops below 1.24V plus A1's hysteresis (about 6mV), A1 enables the rest of the circuit. Power switch Q1 is then cycled on for 6s, or until current comparator A2 turns off the ON timer, whichever comes first. Off-time is fixed at approximately 1.5s. Q1's switching causes current to alternately build up in inductor L1 and discharge into output capacitor C2 via D1, increasing the output voltage. As VFB increases enough to overcome C1's hysteresis, switching action ceases. C2 is left to supply current to the load until VOUT decreases enough to force A1's output high, and the entire cycle repeats. If switch current reaches 1A, causing A2 to trip, switch ON time is reduced. This allows continuous mode operation during bursts. A2 monitors the voltage across 7.2 resistor R1, which is directly related to the switch current. Q2's collector current is set by the emitter-area ratio to 0.5% of Q1's collector current. R1's voltage drop exceeds 36mV, corresponding to 1A switch current, A2's output goes high, truncating the ON time part of the switch cycle. The 1A peak current can be reduced by tying a resistor between the ILIM pin and ground, causing a voltage drop to appear across R2. The drop offsets some of the 36mV reference voltage, lowering peak current. A 22k resistor limits current to approximately 550mA. A capacitor connected between ILIM and ground provides soft start. Shutdown is accomplished by grounding the SHDN pin. The low-battery detector A3 has its own 1.17V reference and is always on. The open collector output device can sink up to 500A. Approximately 35mV of hysteresis is built into A3 to reduce "buzzing" as the battery voltage reaches the trip level. Inductor Selection Inductors used with the LT1304 must be capable of handling the worst-case peak switch current of 1.2A without saturating. Open flux rod or drum core units may be biased into saturation by 20% with only a small reduc-
6
U
tion in efficiency. For the majority of 2-cell or 3-cell input LT1304 applications, a 22H or 20H inductor such as the Sumida CD54-220 (drum) or Coiltronics CTX20-1 (toroid) will suffice. If switch current is reduced using the ILIM pin, smaller inductors such as the Sumida CD43 series or Coilcraft DO1608 series can be used. Minimizing DCR is important for best efficiency. Ideally, the inductor DCR should be less than 0.05, although the physical size of such an inductor makes its use prohibitive in many space conscious applications. If EMI is a concern, such as when sensitive analog circuitry is present, a toroidal inductor such as the Coiltronics CTX20-1 is suggested. A special case exists where the VOUT/VIN differential is high, such as a 2V to 12V boost converter. If the required duty cycle for continuous mode operation is higher than the LT1304 can provide, the converter must be designed for discontinuous operation. This means that the inductor current decreases to zero during the switch OFF time. For a simple step-up (boost) converter, duty cycle can be calculated by the following formula: DC = 1 - [(VIN - VSAT)/(VOUT + VD)] where, VIN = Minimum input voltage VSAT = Switch saturation voltage (0.3V) VOUT = Output voltage VD = Diode forward voltage (0.4V) If the calculated duty cycle exceeds the minimum LT1304 duty cycle of 76%, the converter should be designed for discontinuous mode operation. The inductance must be low enough so that current in the inductor reaches the peak current in a single cycle. Inductor value can be calculated by: L = (VIN - VSAT)(tON /1A) where, tON = Minimum on-time of LT1304 (4s) One advantage of discontinuous mode operation is that inductor values are usually quite low so very small units can be used. Ripple current is higher than with continuous mode designs and efficiency will be somewhat less.
LT1304/LT1304-3.3/LT1304-5
OPERATIO
Table 1 lists inductor suppliers along with appropriate part numbers.
Table 1. Recommended Inductors
VENDOR Sumida Coiltronics Dale Coilcraft SERIES CD54, CD43 CTX20-1 LPT4545 DO3316, DO1608, DO3308 PHONE NUMBER (708) 956-0666 (407) 241-7876 (605) 665-9301 (708) 639-6400
Capacitor Selection Low ESR (Equivalent Series Resistance) capacitors should be used at the output of the LT1304 to minimize output ripple voltage. High quality input bypassing is also required. For surface mount applications AVX TPS series tantalum capacitors are recommended. These have been specifically designed for switch mode power supplies and have low ESR along with high surge current ratings. A 100F, 10V AVX TPS surface mount capacitor typically limits output ripple voltage to 70mV when stepping up from 2V to 5V at a 200mA load. For through hole applications Sanyo OS-CON capacitors offer extremely low ESR in a small package size. Again, if peak switch current is reduced using the ILIM pin, capacitor requirements can be eased and smaller, higher ESR units can be used. Suggested capacitor sources are listed in Table 2.
Table 2. Recommended Capacitors
VENDOR AVX Sanyo Sprague SERIES TPS OS-CON 595D TYPE Surface Mount Through Hole Surface Mount PHONE NUMBER (803) 448-9411 (619) 661-6835 (603) 225-1961
Diode Selection Best performance is obtained with a Schottky rectifier such as the 1N5818. Motorola makes the MBRS130L Schottky which is slightly better than the 1N5818 and comes in a surface mount package. For lower switch currents, the MBR0530 is recommended. It comes in a very small SOD-123 package. Multiple 1N4148s in parallel can be used in a pinch, although efficiency will suffer.
U
ILIM Function The LT1304's current limit (ILIM) pin can be used for soft start. Upon start-up, the LT1304 will draw maximum current (about 1A) from the supply to charge the output capacitor. Figure 3 shows VOUT and VIN waveforms as the device is turned on. The high current flow can create IR drops along supply and ground lines or cause the input supply to drop out momentarily. By adding R1 and C1 as shown in Figure 4, the switch current is initially limited to well under 1A as detailed in Figure 5. Current flowing into C1 from R1 and the ILIM pin will eventually charge C1 and R1 effectively takes C1 out of the circuit. R1 also provides a discharge path for C1 when SHUTDOWN is brought low for turn-off.
VOUT 2V/DIV IIN 500mA/DIV VSHDN 10V/DIV 1ms/DIV
1304 F03
Figure 3. Start-Up Response. Input Current Rises Quickly to 1A. VOUT Reaches 5V in Approximately 1ms. Output Drives 20mA Load
22H* MBRS130L
VIN LBI
SW SENSE LT1304-5 5V 200mA
+
100F 2 CELLS LB0 GND
SHDN ILIM
R1 1M
+
100F
+
C1 1F
SHUTDOWN
1304 F04
*SUMIDA CD54-220
Figure 4. 2-Cell to 5V/200mA Boost Converter Takes Four External Parts. Components with Dashed Lines Are for Soft Start (Optional)
7
LT1304/LT1304-3.3/LT1304-5
OPERATIO
If the full power capability of the LT1304 is not required, peak switch current can be limited by connecting a resistor RLIM from the ILIM pin to ground. With RLIM = 22k, peak switch current is reduced to approximately 500mA. Smaller power components can then be used. The graph in Figure 6 shows switch current vs RLIM resistor value.
VOUT 2V/DIV
I IN 500mA/DIV VSHDN 10V/DIV SHUTDOWN 1ms/DIV
1304 F05
Figure 5. Start-Up Response with 1F/1M Components in Figure 2 Added. Input Current Is More Controlled. VOUT Reaches 5V in 6ms. Output Drives 20mA Load
1000 900
PEAK CURRENT (mA)
800
700 600 500 400
VOUT COUT
GND (BATTERY AND LOAD RETURN)
1304 F07
10
100 RLIM (k)
1000
1304 F06
Figure 6. Peak Switch Current vs RLIM Value
Figure 7. Suggested Layout for Best Performance. Input Capacitor Placement as Shown Is Highly Recommended. Switch Trace (Pin 4) Copper Area Is Minimized
Layout/Input Bypassing The LT1304's high speed switching mandates careful attention to PC board layout. Suggested component placement is shown in Figure 7. The input supply must have low impedance at AC and the input capacitor should be placed as indicated in the figure. The value of this capacitor depends on how close the input supply is to the IC. In situations where the input supply is more than a few inches away from the IC, a 47F to 100F solid tantalum
Low-Battery Detector The LT1304 contains an independent low-battery detector that remains active when the device is shut down. This detector, actually a hysteretic comparator, has an open collector output that can sink up to 500A. The comparator also operates below the switcher's undervoltage lockout threshold, operating until VIN reaches approximately 1.4V. Figure 8 illustrates the input/output characteristic of the detector. Hysteresis is clearly evident in the figure.
8
+
+
U
bypass capacitor is required. If the input supply is close to the IC, a 1F ceramic capacitor can be used instead. The LT1304 switches current in 1A pulses, so a low impedance supply must be available. If the power source (for example, a 2 AA cell battery) is within 1 or 2 inches of the IC, the battery itself provides bulk capacitance and the 1F ceramic capacitor acts to smooth voltage spikes at switch turn-on and turn-off. If the power source is far away from the IC, inductance in the power source leads results in high impedance at high frequency. A local high capacitance bypass is then required to restore low impedance at the IC.
1 2 VIN 3 4 LT1304 8 7 6 5 CIN
LT1304/LT1304-3.3/LT1304-5
OPERATIO
HOURS (H)
10
VLBO 2V/DIV
Figure 8. Low-Battery Detector Transfer Function. Pull-Up R = 22k, VIN = 2V, Sweep Frequency = 10Hz
Battery Life How may hours does it work? This is the bottom line question that must be asked of any efficiency study. AA alkaline cells are not perfect power sources. For efficient power transfer, energy must be taken from AA cells at a rate that does not induce excessive loss. AA cells internal impedance, about 0.2 fresh and 0.5 end-of-life, results in significant efficiency loss at high discharge rates. Figure 10 illustrates battery life vs load current of Figure 9's LT1304, 2-cell to 5V DC/DC converter. Note the accelerated decrease in hours at higher power levels. Figure 11 plots total watt hours vs load current. Watt hours are determined by the following formula: WH = ILOAD(5V)(H)
L1 22H D1
WATT HOURS (WH)
B1 2 CELLS
+
C1 100F
B1 = 2x EVEREADY INDUSTRIAL ALKALINE AA CELLS #EN91 C1, C2 = AVX TPSD107M010R0100 D1 = MOTOROLA MBRS130L L1 = SUMIDA CD54-220
Figure 9. 2-Cell to 5V Converter Used in Battery Life Study
U
1000 100
VLBI 200mV/DIV
1304 F08
1 1 10 LOAD CURRENT (mA) 100 200
1304 F10
Figure 10. Battery Life vs Load Current. Dots Specify Actual Measurements
6 5 4 3 2 1 0
1
10 LOAD CURRENT (mA)
100 200
1304 F11
Figure 11. Output Watt Hours vs Load Current. Note Rapid Fall-Off at Higher Discharge Rates
VIN SHDN
SW SENSE LT1304-5
VOUT 5V 200mA
LB1 ILIM
LB0 GND
+
C2 100F
1304 F09
Figure 11's graph varies significantly from electrical efficiency plot pictured on the first page of this data sheet. Why? As more current is drawn from the battery, voltage drop across the cells' internal impedance increases. This causes internal power loss (heating), reducing cell terminal voltage. Since the regulator input acts as a negative resistance, more current is drawn from the battery as the terminal voltage decreases. This positive feedback action compounds the problem.
9
LT1304/LT1304-3.3/LT1304-5
OPERATIO
Figure 12 shows overall energy conversion efficiency, assuming availability of 6.5WH of battery energy. This efficiency approximates the electrical efficiency at load current levels from 1mA to 10mA, but drops severely at load currents above 10mA (load power above 50mW). The moral of the story is this: if your system needs 5V at more than 40mA to 50mA, consider using a NiCd battery (1/10 the internal impedance) instead of a AA cell alkaline battery.
ELECTROCHEMICAL EFFICIENCY (%)
TYPICAL APPLICATIONS
Super BurstTM Low IQ DC/DC Converter
IQ 10A 200k 2N3906 47k 5V 100mA 33H** MBR0530
+
2 CELLS 100F
LBO LT1304 FB SHDN
LBI
EFFICIENCY (%)
VIN
47k
*1% METAL FILM **SUMIDA CD54-330
10
U
U
100 90 80 70 60 50 40 30 20 10 0 1 10 LOAD CURRENT (mA) 100 200
1304 F12
Figure 12. Overall System Efficiency Including Battery Efficiency vs Load Current. Internal Impedance of Alkaline AA Cells Accounts for Rapid Drop in Efficiency at Higher Load Current
Super Burst Efficiency
90
0.01F
80
SW 3.83M*
VIN = 3V
70 VIN = 2V 60
ILIM GND 1.21M*
+
220F
50
22k
40 0.01
1304 TA03
0.1 1.0 10 LOAD CURRENT (mA)
100
1304 TA04
Super Burst is a trademark of Linear Technology Corporation.
LT1304/LT1304-3.3/LT1304-5
TYPICAL APPLICATIONS
2-Cell to 3.3V Boost Converter
L1* 22H MBRS130L
VIN
+
2 CELLS
C1** 100F
LT1304-3.3 SHDN ILIM
EFFICIENCY (%)
SHUTDOWN *SUMIDA CD54-220 **AVX TPSD107M010R0100
NC
3.3V SEPIC (Step-Up/Step-Down Converter)
VIN 2.5V TO 8V C2 47F 16V L1A* 2 1 SW 4 L1B* LT1304-3.3 SHDN ILIM NC *COILTRONICS CTX20-1 **TOKIN 1E105ZY5U-C103-F AVX TPSD476M016R0150 AVX TPSD107M010R0100 SENSE GND 3 3.3V 300mA MBRS130L C1** 1F
EFFICIENCY (%)
+
VIN
SHUTDOWN
5V SEPIC (Step-Up/Step-Down Converter)
VIN 3V TO 8V L1A* 2 1 SW 4 L1B* LT1304-5 SHUTDOWN SHDN ILIM NC *COILTRONICS CTX20-1 **TOKIN 1E105ZY5U-C103-F AVX TPSD476M016R0150 AVX TPSD107M010R0100 SENSE GND 3 5V 200mA MBRS130L C1** 1F
EFFICIENCY (%)
+
47F 16V
VIN
U
2-Cell to 3.3V Converter Efficiency
90 80
SW SENSE 3.3V 300mA
70 60 50 40 30 0.1 VIN = 3.3V VIN = 2.5V 1.8V VIN = 2.5V 1 10 100 LOAD CURRENT (mA) 1000
1304 TA06
GND
+
C2** 100F 10V
1304 TA05
3.3V SEPIC Efficiency
80 75 70 65 60 55 50
1304 TA07
+
C3 100F 10V
VIN = 4.5V VIN = 3.5V VIN = 2.5V 1 10 100 LOAD CURRENT (mA) 500
1304 TA08
5V SEPIC Efficiency
80 75 70 65 60 55 50
1304 TA09
+
100F 10V
VIN = 6V VIN = 5V VIN = 4V VIN = 3V 1 10 100 LOAD CURRENT (mA) 500
1304 TA10
11
LT1304/LT1304-3.3/LT1304-5
TYPICAL APPLICATIONS
5V to 12V DC/DC Converter
L1* 22H 5V D1
+
47F**
VIN LT1304
SW
EFFICIENCY (%)
SHUTDOWN
SHDN
FB GND 124k 1%
*SUMIDA CD54-220 **AVX TPSD476M016R0150 MOTOROLA MBRS130L
Single Li-Ion Cell to 5V Converter with Load Disconnect at VIN < 2.7V
MBRS130LT3 (5V) 5V
(2.7V to 4.2V)
+
100F 16V
562k 1%
220k VIN NC ILIM LBI SW VOUT VOUT VIN2 LTC1477 VINS EN VIN3 GND NC NC
SINGLE Li-Ion CELL* 432k 1%
*PRIMARY Li-Ion BATTERY PROTECTION MUST BE PROVIDED BY AN INDEPENDENT CIRCUIT **SUMIDA CD54-220 AVX TPSD107M010R0100
12
U
5V to 12V Converter Efficiency
90
85
80
1.07M 1%
12V 200mA
75
+
47F** 16V
70
1304 TA11
65 1 10 100 LOAD CURRENT (mA) 300
1304 TA12
22H**
+
1F
SENSE LT1304CS8-5
+
100F 10V
VIN1
SHDN
GND
LBO
1304 TA13
LT1304/LT1304-3.3/LT1304-5
TYPICAL APPLICATIONS
Negative LCD Bias Generator
L1* 10H
+
2 CELLS 47F ILIM
+
22k 3.3F
* SUMIDA CD43-100 ** MOTOROLA MBR0530
VOLTAGE ADJUST 1kHz PWM INPUT 0V TO 5V
Electroluminescent Panel Driver with 200Hz Oscillator
MUR160 600V 4 EL PANEL CPANEL 20nF 1F 200V
VIN 2V TO 7V
1:12*
+
3 47F 1
6 MBR0530
5V = OPERATE 0V = SHUTDOWN 22k 22k 2N3906 75k 3.3k 1nF
VIN SHDN LBO LT1304
SW FB
D
51k
G ! HI GER 10M AN
22k
L H VO
(3.3M x 3) FMMT458
LBI 0.01F ILIM NC 200Hz GND
50k INTENSITY ADJUST 1/2 BAW56
* DALE LPE3325-A205 TRANSFORMER MEASURES 6.5mm x 8.2mm x 5.2mm (H) (605) 665-9301
+
U
** VIN SW FB LT1304 90.9k 1% GND 1M 1% 110k 1% 1000pF 1.69M 1%
1F CERAMIC -VOUT -14V TO -22V 1mA TO 10mA
**
**
10F 35V EFFICIENCY = 70% TO 75% AT ILOAD 2mA
1304 TA14
TAG
E
22k
22k
1/2 BAW56
1304 TA15
13
LT1304/LT1304-3.3/LT1304-5
TYPICAL APPLICATIONS
2- to 4-Cell to 1kV Step-Up Converter
0.01F 0.01F 0.01F 0.01F 0.01F
VIN 2V TO 6V
+
47F
VIN 0.1F LT1304 SHUTDOWN SHDN ILIM NC
VIN 2V TO 6V VIN
+
47F* SHDN ILIM SHUTDOWN NC
*AVX TPS SERIES TANTALUM OR SANYO OS-CON **SUMIDA CD54-220
14
U
T1* 3 4 0.01F 1 6 MBR0530 0.01F 0.01F 0.01F
SW FB
R1** 500M R2 620k
D
ER ANG
! HI
G
LT H VO
AGE
VOUT = 1.24V 1+
()
R1 R2
VOUT 1kV 250A
GND
* DALE LPE3325-A205 TRANSFORMER MEASURES 6.5mm x 8.2mm x 5.2mm (H) (605) 665-9301 ** IRC CGX-1/2 ALL 0.01F CAPACITORS 250WVDC BAS21 OR MUR130
1304 TA16
2- to 4-Cell to 5V Converter with Output Disconnect
2k L1** 22H
MBRS130L ZTX788B SW SENSE 5V 100mA
LT1304-5
+
GND 22F*
+
220F*
1304 TA17
LT1304/LT1304-3.3/LT1304-5
TYPICAL APPLICATIONS
2-Cell to 5V Converter with Auxiliary 10V Output
MBR0530 1F CERAMIC
2 CELLS
*SUMIDA CD54-220
1304 TA18
2 CELLS
*SUMIDA CD54-220
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of circuits as described herein will not infringe on existing patent rights.
+
U
+
+
+
MBR0530 10F
10V 20mA
L1* 22H
MBRS130L
VIN
SW SENSE 5V 150mA
100F SHDN ILIM SHUTDOWN NC
LT1304-5
+
GND 100F
2-Cell to 5V Converter with Auxiliary - 5V Output
L1* 22H
MBRS130L
VIN
SW SENSE 5V 150mA 1F CERAMIC MBR0530 GND MBR0530 10F -5V 20mA
100F SHDN ILIM SHUTDOWN NC
LT1304-5
+
100F
1304 TA19
15
LT1304/LT1304-3.3/LT1304-5
PACKAGE DESCRIPTION
0.010 - 0.020 x 45 (0.254 - 0.508) 0.008 - 0.010 (0.203 - 0.254) 0- 8 TYP
0.016 - 0.050 0.406 - 1.270 *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
RELATED PARTS
PART NUMBER LTC(R)1163 LT1239 LT1301 LT1302 LT1303 LTC1477 LT1521 DESCRIPTION Triple High Side Driver for 2-Cell Inputs Backup Battery Management System Fixed 5V/12V Step-Up Micropower DC/DC Converter High Output Current Micropower DC/DC Converter Micropower DC/DC Converter Protected Switch 300mA, 12A IQ Low Dropout Regulator COMMENTS 1.8V Minimum Input, Drives N-Channel MOSFETs Easy-to-Use, Fail-Safe Backup Protection 12V/200mA from 5V, 120A IQ, 88% Efficiency 5V/600mA from 2V, 2A Internal Switch, 200A IQ Low-Battery Detector Inactive in Shutdown Ultralow RDS(ON) Switch: 0.07 500mV Dropout at Full Load
16
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977
U
Dimension in inches (millimeter) unless otherwise noted.
S8 Package 8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 - 0.197* (4.801 - 5.004) 8 7 6 5
0.228 - 0.244 (5.791 - 6.197)
0.150 - 0.157** (3.810 - 3.988)
1
2
3
4
0.053 - 0.069 (1.346 - 1.752)
0.004 - 0.010 (0.101 - 0.254)
0.014 - 0.019 (0.355 - 0.483)
0.050 (1.270) BSC
SO8 0695
LT/GP 1195 10K * PRINTED IN USA
(c) LINEAR TECHNOLOGY CORPORATION 1995

▲Up To Search▲

Price & Availability of LT1304

	To Download LT1304 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .